Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093
Fachzeitschrift: Zeitschrift
ISSNs | 0921-5093 |
---|---|
Weitere suchbare ISSN (eISSN) | 1873-4936 |
Publikationen
- 2013
- Veröffentlicht
The effect of main alloying elements on the physical properties of Al–Si foundry alloys
Stadler, F., Antrekowitsch, H., Fragner, W., Kaufmann, H., Pinatel, E. & Uggowitzer, P. J., 2013, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. S. 1-1Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- Veröffentlicht
The influence of microstructure and operating temperature on the fatigue endurance of hot forged Inconel® 718 components
Maderbacher, H., Oberwinkler, B., Gänser, H.-P., Tan, W., Rollett, M. & Stoschka, M., 2013, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. Volume 585, S. 123-131Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- Veröffentlicht
The influence of microstructure and operating temperature on the fatigue endurance of hot forged Inconel (R) 718 components
Maderbacher, H., Oberwinkler, B., Gänser, H.-P., Tan, W., Rollett, M. & Stoschka, M., 15 Nov. 2013, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 585, S. 123-131Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- 2014
- Veröffentlicht
Comparison of microstructural crack paths between hypo-eutectic Al-Si-Cu and Al-Si-Mg cast alloys in high plasticity regimes under rotating bending
Huter, P., Winter, G., Renhart, P., Schwab, M., Oberfrank, S., Grün, F. & Stauder, B., 2014, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 618, S. 578-585Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- Veröffentlicht
Hot-working behavior of an advanced intermetallic multi-phase gamma-TiAl based alloy
Schwaighofer, E., Clemens, H., Lindemann, J., Stark, A. & Mayer, S., 2014, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 614, S. 297-310Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- Veröffentlicht
Microstructural investigation of thermally aged nickel-based superalloy 718Plus
Whitmore, L., Ahmadi, M. R., Stockinger, M., Povoden-Karadeniz, E., Kozeschnik, E. & Leitner, H., 2014, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 594, S. 253-259Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- Veröffentlicht
The microstructure of heat-treated nickel-based superalloy 718Plus
Whitmore, L., Ahmadi, M. R., Guetaz, L., Leitner, H., Povoden-Karadeniz, E., Stockinger, M. & Kozeschnik, E., 2014, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 610, S. 39-45Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- Veröffentlicht
Yield strength prediction in Ni-base alloy 718Plus based on thermo-kinetic precipitation simulation
Ahmadi, M. R., Povoden-Karadeniz, E., Whitmore, L., Stockinger, M., Falahati, A. & Kozeschnik, E., 1 Juli 2014, in: Materials Science and Engineering A. 608, S. 114-122 9 S.Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
Microstructure and temperature dependence of intergranular strains on diffractometric macroscopic residual stress analysis
Wimpory, R., Krempaszky, C. & Stockinger, M., 16 Sept. 2014, in: Materials Science and Engineering A. 618, S. 271-279 9 S.Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)
- 2015
- Veröffentlicht
Elevated temperature mechanical properties of novel ultra-fine grained Cu-Nb composites
Primorac, M.-M., Abad, M. D., Hosemann, P., Kreuzeder, M., Maier, V. & Kiener, D., 2015, in: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 625, S. 296-302Publikationen: Beitrag in Fachzeitschrift › Artikel › Forschung › (peer-reviewed)